Welder for club members to use. Just Putting it out there.
I just want to put it out there... I have a mig and a bit of ability to use it. If anyone is interested in using it please let me know.
I have been slowly working on my brew stand and not everyone has the access so I just wanted to put it out there for use to club members..
If you have a project that you can use it, please let me know.
Scott
Replies to This Discussion
-
Permalink Reply by Thomas F Tomczyk on -
Let me put it out there that I can also offer welding services, but not use of my welder. I am not looking for big projects (8 - 16 hours at most) and I would appreciate any sweat equity that folks would like to put in helping in the areas of measure/cut, drilling, grinding, fitting up (basically everything up to the point of welding). My hourly rate is flexible and decreases as # of hours increases (quantity discount).
I have:
A gas shielded MIG welder (110v, welding up to 1/4" thick)
A plasma cutter (think hot knife through butter, but instead of butter, metal)
A big drill press (6' floor model)
Metal chop saw
4.5" angle grinders
A tubing bender set up for 1" or 1-5/8" tubing (can do other sizes or square by purchasing additional dies, which run $180 and up, you'd have to foot 50% of die cost).
I weld mild steel/cromoly. No aluminum, no stainless. I weld in my garage/driveway (not mobile).
-Tom
-
Permalink Reply by Mike Ribaudo on -
Would you be able to cut 12" holes in the tops of 2 kegs with the plasma cutter? Thanks.
Thomas F Tomczyk said:Let me put it out there that I can also offer welding services, but not use of my welder. I am not looking for big projects (8 - 16 hours at most) and I would appreciate any sweat equity that folks would like to put in helping in the areas of measure/cut, drilling, grinding, fitting up (basically everything up to the point of welding). My hourly rate is flexible and decreases as # of hours increases (quantity discount).
I have:
A gas shielded MIG welder (110v, welding up to 1/4" thick)
A plasma cutter (think hot knife through butter, but instead of butter, metal)
A big drill press (6' floor model)
Metal chop saw
4.5" angle grinders
A tubing bender set up for 1" or 1-5/8" tubing (can do other sizes or square by purchasing additional dies, which run $180 and up, you'd have to foot 50% of die cost).
I weld mild steel/cromoly. No aluminum, no stainless. I weld in my garage/driveway (not mobile).
-Tom
-
Permalink Reply by Greg Garcia on -
Tom, I have a motorcycle gas tank that has a pin hole leak in a weld on the under side. Is this something you could weld for me? I have the tank removed. Let me know. Thanks. 4803351688.
Mike Ribaudo said:Would you be able to cut 12" holes in the tops of 2 kegs with the plasma cutter? Thanks.
Thomas F Tomczyk said:Let me put it out there that I can also offer welding services, but not use of my welder. I am not looking for big projects (8 - 16 hours at most) and I would appreciate any sweat equity that folks would like to put in helping in the areas of measure/cut, drilling, grinding, fitting up (basically everything up to the point of welding). My hourly rate is flexible and decreases as # of hours increases (quantity discount).
I have:
A gas shielded MIG welder (110v, welding up to 1/4" thick)
A plasma cutter (think hot knife through butter, but instead of butter, metal)
A big drill press (6' floor model)
Metal chop saw
4.5" angle grinders
A tubing bender set up for 1" or 1-5/8" tubing (can do other sizes or square by purchasing additional dies, which run $180 and up, you'd have to foot 50% of die cost).
I weld mild steel/cromoly. No aluminum, no stainless. I weld in my garage/driveway (not mobile).
-Tom
© 2012 Created by ASH Editor.
